A Time Switching System Using Atmega328 Microcontroller towards Solving Problem of Electrical Power Wastage

Full Text (PDF, 523KB), PP.18-26

Views: 0 Downloads: 0

Author(s)

Salako Emmanuel Adekunle 1,*

1. Department of Computer Science, FCT College of Education, Zuba-Abuja, Nigeria

* Corresponding author.

DOI: https://doi.org/10.5815/ijigsp.2019.06.03

Received: 14 Nov. 2018 / Revised: 12 Apr. 2019 / Accepted: 22 May 2019 / Published: 8 Jun. 2019

Index Terms

Atmega328 Microcontroller, Design, Implementation, Switching and Time

Abstract

The wastage of electrical power cannot be over-emphasized in FCT College of Education, Zuba-Abuja as many lighting bulbs, street-lights, electrical fans are always ON even when not in use. The college community is characterized by electrical power wastage. However, the motivation for this research was to curtail the electrical power wastage and reduce the high cost of electricity. This research was designed to control ON and OFF time of any electrical appliance connected to its output and could as well be used as a digital clock. The objective of this research was to control the ON and OFF time of air conditioning. The design included a microcontroller (ATMEGA328) that was programmed to achieve the timing operation. The Light Emitting Diode (LED) displayed the ton (Time ON) and the t0ff (Time OFF); four keys set the hour and the minutes; and the relay was activated whenever the time set elapsed, causing the air conditioning to be energized/dis-energized automatically. A time of 3:19 was set to test the ON switching. An air conditioning connected to the developed system was activated at exactly 3:19. Also, a time of 5:57 was set to de-activate the already ON electric bulb. The electric bulb was switched OFF at exactly 5:57. The developed switching system was tested and satisfactorily switched ON and OFF air conditioning as desired and pre-set by the user.

Cite This Paper

Salako Emmanuel Adekunle, "A Time Switching System Using Atmega328 Microcontroller towards Solving Problem of Electrical Power Wastage", International Journal of Image, Graphics and Signal Processing(IJIGSP), Vol.11, No.6, pp. 18-26, 2019. DOI: 10.5815/ijigsp.2019.06.03

Reference

[1]F. M. Abu, H. M. Fida, M. I. Manirul and A. Mohiuddin., “Microcontroller Based Remote Control of Home Appliances," Proceeding of the International Conference on Electrical, Computer and Telecommunication Engineering, held at Bangladesh in December 2012, pp. 511– 514.

[2]S. Aditi, P. Priyanka, N. Kanchan and S. Shital, “Clap Pattern Based Electrical Appliance Control”, International Research Journal of Engineering and Technology (IRJET),2017, vol. 4(2), pp. 902-905.

[3]R. Chintha, P. O. Benny, O. Vijaylaxmi, D. Varsha and B. S. Prasad”, Electrical appliances in home control through IR Remote,” International Journal of Innovative Research in Technology (IJIRT), 2017, vol.  3(9), pp. 16-19.

[4]G. K. Jonathan and S. D. Umar, “Development of a simple programmable control timer,” Leonardo Journal of Sciences, 2008, vol. 12, pp. 175-186

[5]W. Niti and N. Pongpon, “The Development of Smart Home System for Controlling and Monitoring Energy Consumption using WebSocket Protocol,” Materials Science and Engineering, 2017, pp. 1-6.

[6]J. Morgan, “Time Management. Mood House Press, California, 2009

[7]E. A. Salako, “Introduction to BASIC Programming Language,” MAT-Sunshine Prints: Abuja, Nigeria, 2017.

[8]A. Amevi, M. A. Michael and A. Noble “Design, testing and analysis of single phase electronic changeover with security light,” APT Journal of Multidisciplinary Research, 2016, vol. 1(1), pp. 17–24.

[9]O. Bamidele, J. Samuel and O. Omakoji, “Developing an Automatic Switch for Home or Industrial Power Supply Changeover,” British Journal of Applied Science & Technology, vol. 21(4), pp. 1-7

[10]E. Idoko, P. I. Udenze and F. T. Ikule “Design and implementation of three phases automatic change over switch,” International Journal of Advanced Engineering Research and Technology (IJAERT), 2018, 6(7), 435-439.

[11]L. S. Ezema, B. U. Peter and O. O. Harris, O. O. “Design of Automatic Change-Over Switch with Generator Control Mechanism”. Electrical Power and Electronic Development, Department Projects Development Institute, 2012, vol. 3 (3), pp. 125-130.

[12]A. R. Atser, F. N. Gesa, and I. S. Aondoakaa, “Design and Implementation of a 3-Phase Automatic Power Change-over Switch,” American Journal of Engineering Research, 2014, vol. 3 (9), pp. 7-14.

[13][C. A. Osaretin, E. I. Ibhadode and S. O. Igbinovia, “Design and implementation of automatic changeover switch (with step loading) for renewable energy Systems. International Journal for Renewable Energy and Environment, 2016, vol. 2, pp. 179-192.

[14]T. Ilomuanya and U. V. Okpala, “Implementation of the Designed Automatic Change Over System for the Department of Physics, Chukwuemeka Odumegwu Ojukwu University, Uli. International Journal of New Technology and Research, 2016, 2 (4), pp. 130-136.

[15]O. M. Okome and O. Folorunso, “Automatic transfer switch with three phase selector,” International Journal of Scientific & Engineering Research, 2015, vol. 6 (7), pp. 81-87.

[16]A. F. Agbetuyi, A. A. Adewale, J. O. Ogunluyi and D. S. Ogunleye, “Design and construction of an automatic transfer switch for a three phase power generator. International Journal of Engineering Science, 2014, vol 3, pp 57-66