Investigation of Closed Loop Control for Interleaved Boost Converter with Ripple Cancellation Network for Photovoltaic Applications

Full Text (PDF, 308KB), PP.66-72

Views: 0 Downloads: 0

Author(s)

Nithya Subramanian 1,* R. Srinivasan 1 R.Seyezhai 1 Pridhivi Prasanth 1 R.R. Subhesh 1

1. Department of EEE, SSN College of Engineering, Chennai, India, 603110

* Corresponding author.

DOI: https://doi.org/10.5815/ijitcs.2015.09.10

Received: 10 Dec. 2014 / Revised: 3 Apr. 2015 / Accepted: 12 May 2015 / Published: 8 Aug. 2015

Index Terms

Interleaved boost converter, photovoltaic, ripple cancellation network, voltage mode control

Abstract

Conventional sources like fossil fuels were used earlier to satisfy the energy demands. Nowadays these are being replaced by renewable sources like photo-voltaic sources. Photo-voltaic is a method of generating electrical power by converting the energy from the sun into direct current with the use of semiconductor devices that exhibit photovoltaic effect. They do not cause environmental pollution and do not require any moving parts. Different types of DC-DC Converters have been proposed in literature but Inter-leaved boost Converter (IBC) is widely used because of its fast dynamic response and high power density. This paper presents an analysis of the voltage mode control strategies employed by Ripple Cancellation Network (RCN) based two phase Interleaved boost Converter (IBC) for photo-voltaic applications. After analyzing the different Boost converter topologies, the results illustrate that IBC is more efficient than conventional boost converter as it reduces the input current ripple, output voltage ripple, component size and improves its transient response. On adding the Ripple Cancellation Network to the conventional IBC, the output voltage and input current ripple are further reduced without increasing the diode current stress. Adopting the closed loop voltage mode control, the ripple components are found to decrease significantly at the output thereby achieving a higher level of efficiency. A comparison is drawn between open and closed loop voltage control ripple component values. Simulations are carried out using MATLAB/SIMULINK software to verify with the theoretical results.

Cite This Paper

Nithya Subramanian, R. Srinivasan, R.Seyezhai, Pridhivi Prasanth, R.R. Subhesh, "Investigation of Closed Loop Control for Interleaved Boost Converter with Ripple Cancellation Network for Photovoltaic Applications", International Journal of Information Technology and Computer Science(IJITCS), vol.7, no.9, pp.66-72, 2015. DOI:10.5815/ijitcs.2015.09.10

Reference

[1]M. R. Feyzi, S. A. KH. MozaffariNiapour,F. Nejabatkhah, A. Feizi. “Brushless DC Motor Drive Based On Multi-Input DC Boost Converter Supplemented By Hybrid PV/FC/Battery Power System”, IEEE Journal, volume, IEEE CCECE 000442 (2011).

[2]Wuhua Li, Jianguo Xiao, Jiande Wu, Jun Liu, Xiangning He. “Application Summarization of Coupled Inductors in DC/DC Converters”, IEEE Journal, volume, pp. 1487- 1491, (2009).

[3]Guangyong Zhu, Brent A. McDonald, Kunrong Wang. “Modeling and Analysis of Coupled Inductors in Power Converters”, IEEE Journal, volume, pp. 1355 - 1363, (2011).

[4]Ishtiyaq Ahmed Makda , Morten Nymand  . “ Differential Mode EMI Filter Design for Ultra High Efficiency Partial Parallel Isolated Full-Bridge Boost Converter”, IEEE  Journal, volume, 978-1-4673-1792-4/13, (2013).

[5]Kenta Isozumi, Noriyuki Kimura , C. D. ToshimitsuMorizane, Hideki Omori. “Soft Switching DC- DC Converter with Coupling Inductor for Continuos Current Mode Operation” , IEEE Journal

[6]R.Seyezhai. “Design Consideration of Interleaved Boost Converter for Fuel Cell Systems”, IJA EST, volume, pp.323 – 329.(2011).

[7]Saggini S., Mattavelli P., Ghioni M. and Redaelli M., Mixed-Signal Voltage-Mode Control for DCand#x2013;DC Converters With Inherent Analog Derivative Action, Power Electronics, IEEE Transactions on, 23, 1485-1493.

[8]Mohan N., Undeland T. M. and Robbins W. P., Power Electronics - Converters, Applications, and Design (3rd Edition), ed: John Wiley and Sons.

[9]Rashid M.H., Power Electronics: Circuits, Devices and Applications vol. (3rd Edition), Prentice Hall (2003)

[10]R. Seyezhai, B. L. Mathur. “A Comparison of Three-Phase Uncoupled and Directly Coupled Interleaved Boost Converter for Fuel Cell Applications”, IJEEI  Journal, volume,3, (2011).

[11]Yan Dong, Fred. C. Lee, Ming Xu. “ Evaluation of  Coupled Inductor Voltage Regulators”, IEEE Journal, volume, pp. 831 - 837, (2008).

[12]Yu Gu, Donglai Zhang “Interleaved Boost Converter with Ripple Cancellation Network”, IEEE Journal, volume, pp.3860 - 3869, (2013).

[13]Robert S. Balog, Philip T. Krein, “Coupled-  Inductor Filter: A Basic Filter Building Block”, IEEE Journal, volume, pp. 537 – 546 , (2013).

[14]Sathya, P.; Natarajan, R., ‘Design and Implementation of 12/24V Closed loop Boost Converter for Solar Powered LED lighting system, International Journal of Engineering Science &Technology, volume 5 issue 2, February 2013.

[15]Farag. S. Alargt; Ahmed. S. Ashur, ‘ Analysis and Simulation of Interleaved Boost Converter for Automotive Applications’, International Journal of Engineering and Innovation Technology, volume 2, issue 11, May 2013. 

[16]TamalBiswas, G KPanda , P KSaha , S Das, “Design of PWM-Based Sliding-Mode Control of Boost Converter with Improved Performance”, International Journal of Advanced Research in Electrical, Electronics and Instrumentation Engineering, Vol. 4, Issue 2, February 2015.

[17]M.T. Makhloufi, M.S. Khireddine, Y. Abdessemed, A. Boutarfa, “Tracking Power Photovoltaic System using Artificial Neural Network Control Strategy”, International Journal of Intelligent Systems and Applications(IJISA), IJISA Vol. 6, No. 12, November 2014.